Teknobond 120 is a water-based two-component epoxy primer before applying topcoats. It is used to improve adhesion, strengthen and protect various types of surfaces. It does not contain solvents.
APPLICATION
● Concrete surfaces outside and inside the premises.
● Can be used in enterprises where there is constant exposure to chemicals, in food production.
● Suitable for glossy surfaces: granite, tiles, ceramics, glass.
● For vertical and horizontal surfaces.
● Suitable for use in rooms with high humidity.
FEATURES / ADVANTAGES
● Easy and quick application.
● Water-based, odorless.
● Environmentally safe. Can come into contact with drinking water.
● Can be used in rooms without ventilation.
● Suitable for highly absorbent surfaces.
● Vapor permeable.
● High adhesion strength at any application temperature.
NORMS/STANDARDS
Meets the requirements of EN ISO 2811-1
MATERIAL INFORMATION
Packaging
15 kg set
Expiration date
12 months from date of manufacture, when stored in original undamaged packaging.
Storage conditions
Store in unopened and undamaged original packaging in dry conditions at a temperature of +5 °C to +30 °C.
Color/Type
Transparent yellow
Density
Component A: 1.05±0.03 (g/ml)
Component B: 1.10±0.03 (g/ml)
Ready working mixture: 1.07 ±0.03 (g/ml)
Temperature resistance
From - 20 °C to + 60 °C
TECHNICAL INFORMATION
Material base
Epoxy
Mixing proportions
11 units of component A : 4 units of component B (by weight)
Mixture life
~ 2-3 hours
(depending on ambient temperature)
Application temperature
+5 °C - +35 °C (drying time may increase or decrease significantly depending on temperature)
Cost
~ 150-250 g/m2 (as a primer)
~ 500-600 g/m2 (as surface protection from moisture)
Waiting time between layers
24-48 hours
APPLICATION INSTRUCTIONS
SUBSTRATE QUALITY / PREPARATION
The surface must be free from dust, dirt, loose particles, cement mortar residues, oils, silicones and must be dry. The concrete base must be clean, sound and have sufficient compressive strength (at least 25 N/mm²) and tensile strength of at least 1.5 N/mm². Larger damage must be repaired using the appropriate Teknorep/Teknogrout repair compounds.
KNEADING
● Mix component A thoroughly.
● Add component B to component A.
● Mix both components with a low-speed electric mixer (maximum 400 rpm) for 2–3 minutes until smooth.
● Mix the material in the amount you can use, according to the proportion specified by the manufacturer.
CAUSING
Make sure that TEKNOBOND 120 is applied to a solid and thoroughly cleaned surface. TEKNOBOND 120 can be applied with a brush or roller.
It is important to avoid water or pedestrian traffic until the material has fully cured. The surface can be left open to pedestrian/vehicle traffic for 24 hours.
CLEANING THE TOOL
Clean tools and equipment with water immediately after use. Once the material has cured, it can only be removed mechanically.
LIMITATION
● Do not use at temperatures below the minimum and above the maximum permitted
● Low temperatures slow down hardening, high temperatures accelerate it.
● The shelf life of the material depends on the temperature of use and storage.
● If the material is stored at temperatures below 0°C for a long time, crystallization may occur. If the crystals disintegrate when the product is brought to room temperature, the product can be used.
● Do not add foreign substances to the product.
● The component ratio is precisely calculated, do not use less/more of component A or B.
SAFETY MEASURES
The product may cause irritation if it comes into contact with the skin. It is necessary to use work clothes, protective gloves, a mask and glasses. You can also apply a protective cream to your hands before starting work. In case of contact with eyes, immediately rinse your eyes with warm water and consult a doctor.
MATERIAL DATA BASIS
The above technical data are obtained from laboratory tests conducted at a temperature of + 20 °C and a relative humidity of 50% in the Tekno Yapı Kimyasalları laboratory. The results are obtained 28 days after the tests. The actual characteristics of the material may change for reasons beyond our control. Since we are unable to control the installation process and operating conditions, we are only responsible for the quality of the material. The production of materials is periodically optimized and improved, we have the right to make changes to the technical description of the materials without informing the customer.
Delivery options are subject to confirmation by our manager.
Self-pickup from our warehouse in Kyiv – free of charge.
Postpaid "Nova Poshta"
The buyer-recipient of the parcel pays the cost of the goods and a commission of 2% + 20 UAH from the order amount.
Non-cash payment with VAT
After placing and confirming the order, an invoice with payment details will be sent to your email address.
Non-cash payment
After placing and confirming the order, an invoice with payment details will be sent to your email address. The invoice can be paid through a bank branch or via Internet banking.
Attention! This payment method does not provide for card-to-card transfers!
